1/28/2024 0 Comments Ultimaker cura 15.04.6 download![]() This way (with a feller gauge you can 'fell' if the gap it's really 0.1 when calibrating the bed screws.Īfter an autohome x/y can be moved by hand, but Z motor will be blocked (so you can do this operations). Repeat front corners after adjusting the one on the central back of the bed.Īlso you can get a feller gauge and after doing the home, go prepare/move axis/move 0.1mm/move z Then move the hotend to the basic 3 corners and make the nozzle 'kiss' the bed slightly. The third problem is that the printer does not read the files, I put on the SD card, yet I are working with the Cura and records directly to SD card.Įven better. Unable to set the bed, so I spend so the next step and click on resume.Īnd here the same situation, the nozzle moves to the front right of the bed but 15 mm of bed Then I click on the nozzle moves back to the bottom and center of the bed but at about 15 mm of the bed (Sorry but I kutch is a measure for the moment) I rule the bed with the sheet of paper and the adjustment screw.īut the display screen, written Z = -14.09 The second problem happens now, the nozzle moves into position to the left front of the tray. Well I go to the next step and I click resume. So by clicking the buttons nothing works as it should: The first problem occurs during the phase of levelling bed (this is akin to the problem (a) you mention) No problem for the communication check up, temperature and end-stops. And with the bed Calibration Wizard, in English, for this to be clearer on the capture screen. Yes, sorry but my English is not that good. Is your problem one of 1-5 above? If not maybe a video will help as the words you wrote don't make complete sense in English (sorry!). When you print things they are half height.Ĥ) Z works fine usually but sometimes bed falls suddenly for no apparent reason (this is normal - steppers turn off after a minute of no use).ĥ) Z moves one direction but refuses to move the other direction (limit switch problem). ![]() When you try to home it goes all the way down and makes bad noise.ģ) Z moves wrong distance (usually half) so when you home it from the bottom it never reaches the top - if you home near the top it homes properly. Your post is a bit confusing to me so let me explain a few failure modes:Ģ) Z goes wrong direction. ![]() I move to the next position.Īnd the drama is there, the nozzle moves to the back center of the heat bed but 15 mm from the tray, it is impossible for me to set the tray with the adjusting screw.ĭoes anybody know this problem Installing the after-heat bed? And when the nozzle stuck the paper is ok. The heat bed back and muse moves top left, I rule the stage with the adjusting screw and I put a sheet of paper between the nozzle and the board as a consultant. Well I said I manual adjustment I made early enough for the stubborn Z, so I continue. In fact, the button for mounting 0.2 mm down from 10 mm, for mounting the 10 mm down to 0.2 mm, one to descend from 0.2 mm down to 20 mm and that descend to 10 mm down to 30 mm. To recheck the Z abut the setting wizard.Īnd there begins the first problems the buttons to move up to 0.2 mm OR 10 mm does not rise but down. I connect to the printer for setting the heat bed. ![]() ![]() No problem.Īfter I do the verification Ultimaker all is ok. limit setting I put the nozzle in the center as requested, I put the heat bed 1 mm nozzle and I set the stop end race Z. I download cura 15.04.6, then I download the firmware, I followed the heated bed calibration instructions. In the long run, you will be much happier with a full featured slicer running on a desktop or laptop and letting your Raspberry Pi with OctoPrint do what it does best, control and monitor the printer.I finished up my original Ultimaker + printer. ini files.Ĭura, slic3r, and just about all the other slicers available today have a graphical user interface and many of them have the ability to output the gcode directly to OctoPrint. ini file(s) if you want to change any of the slicer settings, or 2) Install the full Cura 15.04.6 on a desktop (or laptop) computer so you can use it to manipulate. You will also have to 1) manually create / edit your. This version of Cura is ancient and if you slice files on the Raspberry Pi while it is actively printing, your printed object could have artifacts or blemishes. provided the set of commands necessary in his post (the third one of this thread). You need to download the source files for Cura 15.04.6, install the compiler(s) necessary, and build the executable image from the source files. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |